Showing posts with label Transportation. Show all posts
Showing posts with label Transportation. Show all posts

Saturday, August 19, 2023

Comparative Cost of Macadamizing (Explained) and Planking the Streets of Chicago.

Since the experiment of macadamizing [1] (aka McAdamize) the streets of our city has been instituted, a great deal of discussion has been had as to the comparative cost and cheapness of this kind of roadbed over the planking in such general use, and articles, pro and con, upon this subject, have found their way into the newspapers.

Some time ago, the City Council ordered Harrison Street to be macadamizing. A number of property holders on that street, whose property was assessed to pay for the improvement, petitioned the Council to have the street planked instead, for the reason, as they alleged, that the latter road bed is cheaper than the former and, the street not being a prominent thoroughfare, quite as useful. The petition was referred to Mr. N.S. Bonton, City Superintendent, with instructions to report to the Council the comparative cost of both planking and macadamizing. 
South Water Street, Chicago, in the 1860s


The cost comparison is between planking one mile of the street, with the necessary filling to raise the street to an equal height with fourteen inches of macadamizing.

The annexed estimates show the cost for planking twelve, sixteen and twenty-four feet wide, with three-inch oak plank; also, the cost of macadamizing one mile the same width.

sidebar
May 12, 1857, Chicago Tribune:  Canal Street was ordered to be Macadamized from Van Buren Street to Old (18th) Street.



Chicago, August 22, 1857.
To plank one mile of street twenty-four feet wide with a three-inch oak plank, spiked with a wrought iron spike to seven, four by six inch, oak stringers, adding sufficient earth to fill up equal to eleven inches and twenty-eight feet in width:
    • Totaled $16,885 ($593,300 today).
For planking one mile of street sixteen feet wide with a three-inch oak plank, spiked with a wrought iron spike to five oak stringers, four by six inches, adding sufficient earth to fill up to eleven inches high and twenty feet wide:
    • Totaled $11,703 ($411,200 today).
For planking one mile of street twelve feet wide with a three-inch oak plank, spiked with a wrought iron spike to four oak stringers, four by six inches, adding sufficient earth to fill up to eleven inches high and sixteen feet wide:
    • Totaled $9,201 ($323,300 today)
Estimate of cost of macadamizing one mile of the street, one course of stone broken to four-inch maximum diameter, eight inches deep, and covered with one course of stone, broken to two and one-quarter inches maximum diameter, six inches deep, also to grade the road-bed so as to make a suitable face for the stone:
    • Twenty-Four Feet Wide; $15,644 ($549,681 today)
    • Sixteen Feet Wide; $10,516 ($369,500 today)
    • Twelve Feet Wide; $8,008 ($281,375 today)
We are informed by the Superintendent that the estimates for macadamizing are made at what it would cost the city to do the work-by-day labor but that it is probable the same work could be contracted for at nearly a thousand dollars less per mile. 

sidebar
September 8, 1859, Chicago Tribune:  A request to the Horse Railway Company to make sure that their road is well [water] sprinkled, particularly on the Macadamized part where the dust is already insufferable.

These estimates, it must be remembered in forming an opinion as to the best mode of making a roadbed, are for the first cost of the work and have no reference to the expense of keeping it in good order, which is quite as important a consideration as the other. It is to be regretted that the report of the Superintendent does not contain at least some approximate estimates upon this point. It would be scarcely satisfactory to those who we pay for street improvements to tell them that this or that method is the cheapest at the outset than any other when in fact, at the expiration of five to ten years, it may be found the most expensive, owing to the cost of repairs necessary to keep the street in passable condition. The public will be far more capable of forming a correct judgment as to the comparative value of the two kinds of improvement when it is furnished with at least an approximate estimate of the cost of keeping each one in good repair. In the absence of any such estimates, the controversy between the advocates of planking and macadamizing will probably be continued with unabated pertinacity.

There are some objections to macadamizing which are entitled to the serious consideration of our readers, the most important of which, so far as comfort and health are concerned, is dust. All experience shows that macadamized roads, by the time they are worn down to a comfortable smoothness, are covered with fine dust, which is not only excessively disagreeable but most injurious to eyes and lungs. This dust is constantly accumulating by attrition until the whole material of which the road is composed is either ground up or sunk beneath the surface of the earth. Macadamize Harrison or any other street, and it will share the fate of all other macadamized roads; either the atmosphere will be constantly filled with minute particles of pulverized stone, or the street, from being well watered, covered with stone paste, if it may be so called, from one to six inches deep. How much consideration may be given to this drawback is somewhat uncertain when it is remembered that, to a far greater extent than it should, the question of immediate cheapness controls the public decision as to the method to be chosen. The Superintendent has decided that macadamizing is the least expensive at the start, and with many persons, this is quite sufficient to determine the matter.

A word as to the much abused planking. Some of our citizens may recollect the planking put down many years ago on Lake Street, between State and Dearborn Streets. If we remember rightly, the planks were four inches thick, having been made by ripping eight-inch square timber. After it had been in place some seven years, it was taken up to lay a gas pipe for some analogous purpose. A friend who was passing as the time assures us that he examined the planks, then temporarily removed them, saw them sawed across and that they were not at all decayed. The only loss they appeared to have sustained was from the mechanical attrition of the wheels and horses' feet which had passed over them, and that was inconsiderable. The material seemed to be perfectly good for three more years of service.

It deserved to be carefully considered whether substantial planking of this character will not require fewer repairs than macadamizing, especially if laid upon a well-drained roadbed of sand or gravel.  We think such a planking, thoroughly laid down, would be good for ten years at least. A great deal of the planking heretofore done has been so imperfectly executed that is has, we think, produced a wrong impression as to the usefulness and durability of that mode of covering streets.

The estimates of the Superintendent are satisfactory so far as they go. Still, we trust that that officer, or some other person possessing the necessary data, will furnish the public with the cost per mile of the kind of planking we have indicated, and also a comparative estimate of the durability, cost of repairs, etc., of such planking and macadamizing. The subject is one of great importance, and now, at the very onset, it is best that the public should be supplied with all possible information relative to this substitution of macadamizing for planking the street of minor importance, for they take it for granted that the principal thoroughfares will be covered with much better material than either of them.


Compiled by Dr. Neil Gale, Ph.D.



[1] What is a "Macadamized" Street?
A macadamized street is a road that is made of crushed stone that is compacted into layers. The name comes from the Scottish engineer John Loudon McAdam, who invented the process in the early 19th century.

Macadamized roads are characterized by their durability and ability to withstand heavy traffic. They are also relatively inexpensive to construct and maintain.

The basic principle of macadamization is to use crushed stone of different sizes to create a roadbed that is both strong and porous. The largest stones are placed at the bottom, followed by smaller stones and then a layer of fine gravel. The stones are compacted using rollers or tamping machines, which helps to create a smooth, even surface.

In some cases, a binder material, such as asphalt or tar, may be added to the macadam to help bind the stones together and prevent them from shifting. However, McAdam originally designed his roads to be unbound, relying on the weight of traffic to compact the stones and create a stable surface.

Macadamized roads were first introduced in the United States in the early 1820s and quickly became the standard for road construction. They were used to build many of the major highways and roads in the country, and they continue to be used today in some areas.

Advantages of macadamized streets: Durable and can withstand heavy traffic, Drains well, preventing mud, relatively inexpensive to construct, and can be used in a variety of climates.

Disadvantages of macadamized streets: They can be noisy, dusty, slippery in wet weather, and requires regular maintenance.

Thursday, August 17, 2023

Chicago Tribune, Port of Chicago Article, April 18, 1849 (First Newspaper).

In 1849, there was quite a bit of shipping traffic in Chicago.

VIA LAKE MICHIGAN
ARRIVED
April 20, 1849:
Schooner, J.C. Spencer, Muskegon—80 meters (262.5 ft) lumber.

April 23, 1849: 
Brigantine, Helfenstein, Milwaukee—ballast
Schooner, Amanda Harwood, Grand Haven—90 meters (295 ft)
Schooner, Bowen, Kalamazoo—35 meters (115 ft) lumber, 16 meters shingles (52.5 ft)
Schooner, Muskegon, Muskegon— 70 meters (230 ft)
Schooner, Niagara
Schooner, Ronicus
Schooner, Telegraph, Grand Haven—100 meters (328 ft) lumber.

CLEARED
April 21, 1849:
Sloop Michigan, Buffalo—343 hides, 8 pkg sundries, 752 barrels flour, 179 barrels pork
Propeller Princeton, Buffalo—1140 barrels beef, 200 hides, 30 pkg furs


VIA THE CANAL
ARRIVED
April 21, 1849:
Shakespeare, Joliet

April 23, 1849:
Granger, Athens (renamed Lemont in 1850)
Wm. Giles, Athens (renamed Lemont in 1850)

CLEARED
April 21, 1849:
Calaract, LaSalle
Diamond, LaSalle
General Davis, LaSalle
General Fry, Lockport
Hollister, LaSalle
Indians, LaSalle
St. Louis, LaSalle
Wasp, Joliet

April 23, 1849:
Chicago, LaSalle
J.T. McDougal, Joliet
Wm. Giles, Athens (renamed Lemont in 1850)

Brigantine - A brigantine is a two-masted sailing vessel with a fully square-rigged foremast and at least two sails on the main mast: a square topsail and a gaff sail mainsail (behind the mast). The main mast is the second and taller of the two masts.
Propeller - The first propeller ship was invented by John Ericsson in 1836, and the first commercial propeller ship was the SS Archimedes, which was launched in 1838.
Schooner - Schooners were used to transport cargo along the coasts and between islands. They were particularly well-suited for this purpose because they could sail close to shore and in shallow waters. This picture is a replica of the 1847 C.W. Lawrence.
Sloop - A sloop is a sailboat with a single mast typically having only one headsail in front of the mast and one mainsail aft of (behind) the mast. Such an arrangement is called a fore-and-aft rig and can be rigged as a Bermuda rig with triangular sails fore and aft or as a gaff-rig with triangular foresail(s) and a gaff rigged mainsail.



Compiled by Dr. Neil Gale, Ph.D.

Friday, August 11, 2023

Automobile Polo was played at Chicago's Comiskey Park on June 5, 6, 7, and 8, 1913.

Chicago Tribune, Monday, July 28, 1902.
The newest twentieth-century game is called automobile polo. The name, however, has already been found too long and has been conveniently abbreviated to "auto polo." An interesting exhibition of auto polo was given last week on the field of the fashionable Dedham Polo Club of Boston. Mr. Joshua Crene Jr., a member of this club and an expert polo player, made a series of polo strokes from his automobile to the amazement of polo enthusiasts. Mr. Crane is a clever all-around athlete and adept at handling an automobile as well as a polo mallet.

The play is executed so quickly that an unpracticed eye has difficulty following it. The nimble little mobile machines used in the game are capable of developing a speed of about forty miles an hour in a few feet and can be brought to a standstill practically within their own lengths.

Auto polo was a dangerous but popular motorsport that originated in the United States in 1911. It was similar to equestrian polo, but instead of horses, players used cars. The sport was played at fairs, exhibitions, and sports venues across the United States and Europe until the late 1920s. Auto polo was dangerous because of the high speeds and the risk of collisions. Players and spectators were often injured or killed, and vehicles were often damaged.
Auto Polo played at Chicago's Comiskey Park on June 5, 6, 7, and 8, 1913.


Almost as soon as automobiles became somewhat practical, people were figuring out dangerous and fun things to do with them.

The earliest automobiles were typically rich folks’ novelties, which may explain why, in 1902, Joshua Crane, Jr., a polo enthusiast active with the Dedham Polo Club of Boston, decided to put on an exhibition polo match wherein Mobile Runabouts replaced horses.

That it might not have been the safest endeavor can be seen from a surviving photograph of the match catching one of the drivers/mallet men doing a header into the ground, about to be run over by his own steed.

Chicago Tribune, Friday, June 5, 1913
Chicago will get its first taste of auto polo on June 5 when a four days series between teams representing Chicago and New York will be started at Comiskey Park. A syndicate of Chicago men is promoting contests. The first game will be played on the afternoon of June 5, followed by another at night, then by others as follows: The afternoon and night of June 6, the night of June 7, and afternoon and night of June 8.


Just exactly how dangerous it was is hard to tell. The risk of injury to both competitors and spectators eventually put an end to the practice in the late 1920s, but a contemporary account says that deaths were rare. It’s clear that some of the danger might have been exaggerated by staged photographs, but broken bones were apparently not uncommon. In some photos, it seems that competitors wore leather football helmets, showing there was at least some concern about safety.

Though Mr. Crane put on the first auto polo match, it was a Topeka, Kansas, Ford dealer who turned it into an organized sport.

Ralph “Pappy” Hankinson saw polo with cars as a way of promoting the sale of the Model T. The first match Hankinson organized took place in an alfalfa field near Wichita on July 20, 1912, with four cars, eight players, and a reported crowd of 5,000 spectators. Each car carried a seat-belted driver and a free-standing mallet man who had to hang on—often unsuccessfully. The ball was the size of a basketball (some accounts say it was, in fact, a basketball), and after learning something about physics and inertia, weights were added to the mallets so they didn’t “backfire” when striking the balls. Stripped-down Model Ts were fitted with crude roll bars to protect the driver and the cars’ radiators. Speeds were not high, never more than 35 mph, but high enough for mayhem.


Auto polo was invented before the radio, let alone television, so it shouldn’t be a surprise that Hankinson’s idea quickly caught on. Under the Auto Polo Association, local leagues were founded across the United States, and a large exhibition of the sport was staged in Washington, D.C.’s League Stadium in November 1912.

Hankinson sent exhibition teams to England, Europe, and even the Philippines to promote the sport. In 1913, auto polo became the first motorsport to be featured at the Canadian National Exhibition. Britain’s The Auto magazine was impressed but described it as a “lunatic game” that they hoped would not catch on in the UK.

By the 1920s, New York City and Chicago were hosting daily auto polo matches, with some of the games played at NYC’s famous Madison Square Garden.


Many car racing fans today disavow their interest in crashes, but that was genuinely part of the appeal of auto polo. By the end of the matches, the cars were either severely damaged or completely demolished. Hankinson’s own accounting of damages to the cars used by his British and American auto polo teams in 1924 lists 1,564 broken wheels (most cars used wooden spoked “artillery” wheels), 538 unusable tires, 66 broken axles, 10 cracked engines and 6 completely destroyed cars.

While injuries to competitors were frequent, and even spectators were not infrequently hurt by balls flying into the stands or runaway cars, it appears that economics, not concerns about safety, put an end to auto polo.

According to the book Bain’s New York: The City in News Pictures 1900-1925, as the 1920s wore on, the cost of fixing and replacing the cars became too costly. By then, organized car racing was well established. If that wasn’t dangerous enough, there were board-track motordromes and walls of death. So as dangerous as auto polo must have been, it might have seemed a bit quaint during the Roaring Twenties.

In any case, auto polo was a real thing—loony but real.
Auto Polo—No car but the Model T Ford of the
early 1900s had the forward and reverse speeds
and brakes applied by foot pedals. The throttle was
operated by hand, and it was the transmission
system that made such maneuvers possible.

The Dedham Polo Club first used Mobile Runabouts for their exhibition games in 1902. 
1902 Stanley Stick-Seat Runabout.


Unlike equestrian polo, which requires large, open fields that can accommodate up to eight horses at a time, auto polo could be played in smaller, covered arenas during wintertime. This factor greatly increased its popularity in the northern United States. The game was typically played on a field or open area that was a least 300 feet long and 120 feet wide, with 15-foot wide goals positioned at each end of the field. The game was played in two halves (chukkers), and each team had two cars and four men in play on the field at a given time.
The first auto polo cars used by the Dedham Polo Club were unmodified, light steam-powered Mobile Runabouts that seated only one person and cost $650 ($22K today). 




As the sport progressed, auto polo cars resembled stripped-down Model T's. Usually, they did not have tops, doors or windshields, with later incarnations sometimes outfitted with primitive rollbars to protect the occupants. Cars typically had a seat-belted driver and a mallet man that held on to the side of the car and would attempt to hit a regulation-sized basketball toward the goal of the opposing team, with the cars reaching a top speed of 40 miles per hour and while making hairpin turns. The mallets were shaped like croquet mallets but had a three-pound head to prevent "backfire" when striking the ball at high speeds.

The Truth About Cars
Edited by Dr. Neil Gale, Ph.D.

Monday, July 31, 2023

The First Nine Stagecoach Routes out of Chicago.

The earliest stagecoach routes were established in 1832 through the 1840s as Chicago rapidly grew and became a transportation hub. The routes had stops to change teams, for meals, lodging, and nature calls. 


The stagecoaches allowed people to travel long distances quickly and were primarily carefree as paid passengers but for road and weather conditions. Transportation played an essential role in the steady growth of Chicago. 
  • Chicago─Fullersburg (Oak Brook, today) route was the first stagecoach route out of Chicago. The route fare was 10¢ ($3.25 today) for the 15 miles trip between Chicago and Fullersburg. Frink, Bingham & Co. Stagecoach was established in 1832 by John Frink and Charles K. Bingham. The Chicago to Fullersburg route followed the "Indian Boundary" line drawn between the Potawatomi and Ojibwe Indian tribes in 1816. The line ran through what is now Cook County, Illinois. The Indian Boundary line connected Chicago with the Des Plaines River, which is a tributary of the Illinois River, which in turn, is a tributary of the Mississippi River. Chicago's population exploded. The Chicago and Aurora Plank Road was built along the Indian Boundary in 1834 and was one of the first plank roads in Illinois. The Chicago and North Western Railroad was built along the Indian Boundary in the 1850s.
  • Chicago─Galena route was the most popular stagecoach route in Illinois. The trip took about five days. A single trail linking Chicago to Galena was formally established in 1839 by John Frink and Martin Walker, who, together in 1840, established Frink, Walker & Co., Stage Line in Chicago. It spurred economic growth in both cities and the birth of many villages that began as stagecoach stops and soon supporting businesses poped-up.
  • Chicago─Peoria route was first established in 1833 when a one-horse stagecoach was placed in service between the two towns, which took 2 days (24 hours). A two-horse wagon was put into service the following year, and the route was extended southwest to Ottawa. The stagecoach line expanded to include Aurora, Joliet, and Bloomington stops. The stagecoach route continued to operate into the 1850s when it was replaced by the railroad.
  • Chicago─Rockford stagecoach route was among the earliest in Illinois. It was established in 1835 by John Kinzie. The route linked Chicago, a quickly growing town (Inc. Aug.12, 1833), with the village of Rockford, which was located on the Rock River. A popular route, coaches were often crowded, and the trip could be rough and uncomfortable. However, the route was also relatively fast, taking about 12 hours. This route was replaced by the Chicago and Galena Union Railroad in 1850. 
  • Chicago─Milwaukee was a Lake Michigan paddleboat route. The distance between Chicago and Milwaukee in about 12 hours by paddleboat at the end of the 1830s. The fastest paddleboat on the Chicago─Milwaukee route was called the 'Milwaukee,' which was put in service in 1839. The Milwaukee cruised 12 miles per hour, making the trip between Chicago and Milwaukee in just under 10 hours. Three meals, snacks, and perhaps Beer were available.
  • Chicago─Detroit route took about four days to travel. Many stagecoach stops, changing horses and drivers, perhaps a different coach, saloons to eat and board, or boarding houses for a night's stay. 
  • Chicago─Joliet stagecoach route was initially operated by the Chicago and Joliet Stage Company as a mail and passenger route. The stagecoaches traveled round trip between Chicago and Joliet three days a week. The one-way trip took about four hours.
  • Chicago─Aurora route was initially operated by the Chicago and Aurora Stage Company in 1842 as a mail route, adding a large passenger carriage. The 4-horse stagecoaches traveled between Chicago and Aurora, a 30-mile trip that took about three hours, twice a day, each leaving at six in the morning and at three in the afternoon, making it possible to travel back and forth and be back home for supper. The route was often dangerous, prone to flooding and bandits. 
  • Chicago─Elgin The first stagecoaches on the Chicago─Elgin route began operating in 1838. The Chicago and Elgin Stage Company initially operated the route primarily as a mail route and passenger transport. The stagecoaches traveled between Chicago and Elgin twice a day, and the trip took about two hours. The Chicago─Elgin stagecoach ceased operating in the late 1850s, as railroads became the dominant mode of transportation, U.S. Mail, and shipping in the Midwest and beyond. 
What Stagecoach Travel in 1830s Chicago and Illinois was really like. 

The stagecoaches were eventually replaced by railroads, but they played an essential role in the early development of Chicago and surrounding areas. They connect Chicago to other parts of the state and the country, which promoted the city's growth.

Compiled by Dr. Neil Gale, Ph.D.

Saturday, June 3, 2023

The Tom Thumb, America's First Steam Locomotive (1830), at the 1933/34 Chicago World's Fair.

In the 1820s, the port of Baltimore was in danger. The threat came from the newly opened Erie Canal and the proposed Chesapeake and Ohio Canal construction that would parallel the Potomac River from Washington, D.C., to Cumberland, Maryland. These new water routes promised a commercial gateway to the West that would bypass Baltimore's thriving harbor and potentially hurl the city into an economic abyss. Something had to be done.

The local entrepreneurs looked across the Atlantic to England and found an answer in the newly developed railroad. In 1828, the Maryland syndicate, led by Charles Carroll ─ a signer of the Declaration of Independence ─ broke ground for the Baltimore and Ohio Railroad. The railroad aimed to connect Baltimore with the Ohio River and the West. Initially, the railroad's power was to be provided by horses. However, it soon became apparent that animal muscle was no match for the long distances and mountainous terrain that would have to be traveled. The solution lay with the steam engine.


By 1830, the B&O Railroad had extended its track from Baltimore to the village of Ellicott's Mills, thirteen miles to the West. The railroad was also ready to test its first steam engine, an American-made locomotive Peter Cooper of New York engineered.

It was a bright summer's day and full of promise. Syndicate members and friends piled into the open car pulled by a diminutive steam locomotive appropriately named the "Tom Thumb" with its inventor at the controls. The outbound journey took less than an hour. On the return trip, an impromptu race with a horse─drawn car developed. The locomotive came out the loser. It was an inauspicious beginning. However, within a few years, the railroad would become the dominant form of long─distance transportation and relegate the canals to the dustbin of commercial history.

Mr. Cooper's engine boiler was smaller than today's kitchen oven in a standard size range. It was about the same diameter but at most half as high. It stood upright in the car and was filled with vertical tubes from above the furnace, which occupied the lower section. The cylinder was just 3½ inches in diameter, and the speed was achieved by gears. No natural draught could have been sufficient to keep up steam in so small a boiler, and Mr. Cooper used a blowing apparatus driven by a drum attached to one of the car wheels, over which passed a cord that in its turn worked a pulley on the shaft of the blower.

Mr. Cooper's success was such as to induce him to try a trip to Ellicott's Mills; in an open car, the first used upon the road, already mentioned, having been attached to his engine and filled with the directors and some friends, the speaker among the rest, the first journey by steam in America was commenced. The trip was most enjoyable. The curves were passed without difficulty at a speed of six miles an hour; the grades were ascended with comparative ease; the day was fine, the Company in the highest spirits, and some excited gentlemen of the party pulled out memorandum books, and when at the highest speed, which was 8 miles per hour, wrote their names and some connected sentences. The return trip from Ellicott's Mills, a distance of thirteen miles, was made in 57 minutes, averaging 6.8 miles per hour. The top speed was about 10 miles per hour.


But the triumph of this Tom Thumb engine was not altogether without a drawback. The great stage proprietors of the day were Stockton & Stokes. On this occasion, a gallant gray of incredible beauty and power was driven by them from town, attached to another car on the second track. The Company had begun making two tracks to the Mills and met the engine at the Relay House on its way back. From this point, it was determined to have a race home; the start being even, away went horse and engine, the snort of the one and the puff of the other keeping time.

At first, the gray had the best of it, for his steam would be applied to the greatest advantage on the instant, while the engine had to wait until the rotation of the wheels set the blower to work. When the engine's safety valve lifted, the horse was a quarter of a mile ahead, and its thin blue vapor showed excessive steam. The blower whistled, the smoke blew off in vapory clouds, the pace increased, the passengers shouted, the engine gained on the horse, and soon it lapped them him. The race was neck and neck, nose and nose, then the engine passed the horse, and a grand hurrah hailed the victory.
The first steam engine to operate on a commercial track in the United States, the Tom Thumb became famous for its race against a horse-drawn car on August 25, 1830, from Ellicott's Mill to Baltimore.


But it was not repeated; for just at this time, when the gray's master was about giving up, the band which drove the pulley that drove the blower slipped from the drum, the safety valve ceased to scream, and the engine for want of breath began to wheeze and pant. In vain, Mr. Cooper, his own engineman and fireman, lacerated his hands to replace the band upon the wheel. In vain, he tried to urge the fire with light wood; the horse gained on the machine and passed it, and although the band was presently replaced, and steam again did its best, the horse was too far ahead to be overtaken and came in the winner of the race."

The Tom Thumb was salvaged for parts in 1834.

In the 1933-34 Century of Progress World's Fair in Chicago, the Tom Thumb and the DeWitt Clinton steam locomotives were part of the "Wings of a Century" transportation pageant: 
A one-horse chaise (shay), a light, covered, two-wheeled carriage for two persons.


"Just south of Thirty-first Street, on the lakeside, you may watch the dramatization of this century of progress in transportation, the pioneer in the field of communication. On a triple stage, in an outdoor theater, two hundred actors, seventy horses, seven trail wagons, ten trains, and the largest collection of historical vehicles ever to be used, operating under their own power, present "Wings of a Century." Here is the "Baltimore Clipper," the fastest boat of them all. From 1825 to 1850, the "Tom Thumb," the first locomotive of the B&O, the De Witt Clinton, from the old Mohawk & Hudson (New York Central), the Thomas Jefferson (1836) of the Winchester & Potomac (first railroad in Virginia) than the old "Pioneer," the Northern Pacific engine of 1851 a giant locomotive of today (the 1930s) and the 1903 Wright brothers' first airplane.
This replica of the DeWitt Clinton was built for the 1893 World's Columbian Exposition.
Note the barrels of water for the engine.





Compiled by Dr. Neil Gale, Ph.D. 

The DeWitt Clinton Steam Locomotive at the 1893 and 1933/34 Chicago World's Fairs.

The New York Central Railroad built the DeWitt Clinton in 1831, which began the Mohawk & Hudson Railroad (M&H), a New York City predecessor (NYC)They also built this working replica of the DeWitt Clinton for the 1893 World's Columbian Exposition in Chicago.

sidebar
The Tom Thumb Locomotive was the first American-built steam locomotive to operate on a common-carrier railroad. It was designed and constructed by Peter Cooper in 1829 to convince owners of the newly formed Baltimore and Ohio Railroad (B&O;  now CSX) to use steam engines; it was not intended to enter revenue service.

In the 1933-34 Century of Progress World's Fair in Chicago, the DeWitt Clinton and Tom Thumb steam locomotives were part of the "Wings of a Century" transportation pageant: 

"Just south of Thirty-first Street, on the lakeside, you may watch the dramatization of this century of progress in transportation, the pioneer in the field of communication. On a triple stage, in an outdoor theater, two hundred actors, seventy horses, seven trail wagons, ten trains, and the largest collection of historical vehicles ever to be used, operating under their own power, present "Wings of a Century." Here is the "Baltimore Clipper," the fastest boat of them all. From 1825 to 1850, the "Tom Thumb," the first locomotive of the B&O, the De Witt Clinton, from the old Mohawk & Hudson (New York Central), the Thomas Jefferson (1836) of the Winchester & Potomac (first railroad in Virginia) than the old "Pioneer," the Northern Pacific engine of 1851 a giant locomotive of today (the 1930s) and the 1903 Wright brothers' first airplane.
A one-horse chaise (shay), a light, covered, two-wheeled carriage for two persons.


There is a one horse chaise, like George Washington traveled in, and covered wagons and stage coaches of the California Gold Rush 1848 to 1855 days."

The DeWitt Clinton was the first steam locomotive built for service in New York State, and it made its inaugural run on August 9, 1831, connecting Albany and Schenectady in New York State. It ran on rails made of wood or iron, laid on the ground to create a track.
This replica was built for the 1893 World's Columbian Exposition. Official Photograph. Note the barrels of water for the engine.


It was named after DeWitt Clinton, the governor of New York State responsible for the Erie Canal, a competitor to the railroad. DeWitt Clinton's first run was a success, and it helped to pave the way for the development of the railroad industry in the United States.
At the Louisiana Purchase Exposition, aka St. Louis World's Fair, held in 1904.





The DeWitt Clinton was a 0-4-0 steam locomotive.

sidebar
0-4-0 represents one of the simplest possible types, with two axles and four coupled wheels, all of which are driven.
The locomotive was powered by a coal-fired boiler, with a top speed of about 15 miles per hour. The DeWitt Clinton was a small locomotive. It played an essential role in demonstrating the feasibility of steam-powered locomotives in the United States for transportation purposes. It paved the way for the rapid expansion of the railroad industry and the subsequent development of the American transportation system.
Lionel O-Gauge DeWitt Clinton
 



Lionel O-Gauge DeWitt Clinton. (0.25" to a Foot) [runtime 12:41]
It was Also Available in H
O-Gauge (3.5 mm to a Foot). 

Comparing this train with modern trains, the 15 miles per hour was considered a terrific speed, and the accommodations afforded by the coaches were considered the height of comfort.

ADDITIONAL READING:  

Compiled by Dr. Neil Gale, Ph.D.

Sunday, March 26, 2023

The South Side Rapid Transit 'L' Railroad (CTA Green Line), extended for the 1893 World's Fair.



Chicago would start its first elevated 'L' train line in 1888. 



The first 'L' line ran to the south side, known as the "Alley L" because its elevated tracks were squeezed above the alley between State Street and Wabash Avenue downtown, pulled by steam locomotives.



It was extended to reach Jackson Park when Chicago was chosen to host the World's Fair in 1890. 

Jackson Park was a terminal on the Jackson Park Branch of the Chicago 'L.' The station opened on May 12, 1893, and closed on October 31, 1893, with the conclusion of the World's Columbian Exposition.
The 'L' station in Jackson Park, inside the 1893 Columbian Exposition fairgrounds. Architecturally, the station was a simple shed covering the concourse between the stairs and the platforms. The 'L' platforms are behind the shed on the left, while the fair's Intermural Railway and its connection are on the right.




The line was electrified on July 27, 1898.

Only one train station from that 'L' line remains at Garfield Boulevard near the University of Chicago.

Compiled by Dr. Neil Gale, Ph.D. 

Saturday, March 25, 2023

The History of the Illinois Traction System, later, Illinois Terminal Railroad Company. (1901-1982)

Illinois Traction System Service 1901-1937
Before our paved highways connected places in Illinois, we went by train. The reason was simple. Dirt roads were the standard of intercity travel as the 18th century ended. Champaign businessman William B. McKinley (no relation to the President) had a better idea: Connect areas of Central Illinois by railroad. The solution he finally arrived at was a railroad powered by electricity. So, the region entered the era of electric interurbans in 1901.

Petersburg native McKinley was a University of Illinois graduate who made a considerable fortune in local banking and investments. By 1902, he was already a generous benefactor of the University and a Trustee. He also was a major player in getting the Illinois Power and Light Company up and running. That company perfectly blended McKinley's vision for a railroad linking Central Illinois communities by electric rail.

It started in Danville in 1901 when Danville and Westville were linked by electric rail. McKinley's first great line was completed in 1903, and Champaign-Urbana was connected by electric rail to Danville.
Eastbound № 221 stations stop at the Village of Illiopolis (Springfield Metro) depot, 1907.
The Illinois Traction System was incorporated in 1904, which consolidated many small power companies with the electric railroad. 

But McKinley had other interests; they were political. By 1905, he held a seat in the House of Representatives; by 1921, he was one of Illinois' Senators. He slowly turned the management of the railroad over to professionals.

McKinley left a legacy as his life phased into Republican politics. In 1910, he built the still-used and still-named McKinley Bridge across the Mississippi to bring his electric cars into St. Louis.
Business Car № 233 inspects the Emery Substation (7 miles north of Decatur) 1910.


The early days of the Illinois Traction System were so profitable they attracted investors like Clement Studebaker of the South Bend automobile family and Chicago utility giant Samuel Insull. 

In the 1920s, The Illinois Traction System was thriving. Its many routes offered service all over Central and Southern Illinois.
An Illinois Traction Conductor. c.1912
In 1923, the railroad was made an Illinois Power and Light Company subsidiary. The following decades saw massive growth of this railroad that would eventually sprawl over 400 miles of track in Illinois, connecting Danville with St. Louis. 

By 1926, these two influential businessmen essentially owned the Illinois Traction System. Why was a Central Illinois electric railroad attractive to big-money people like Studebaker and Insull?

It was very profitable and ran many routes not covered by the steam locomotive system. For years, the route from Peoria to St. Louis was a monopoly of the Illinois Traction System. Better yet, these electric trains carried freight, which enhanced profits. In areas where the Illinois Traction System did compete with steam railroads, it made arrangements to pick up freight and promoted its passenger service so successfully that many potential rail passengers preferred the electric smoothness of this flourishing interurban.
The new Class "C" № 1579 was released from the Decaur Shop on October 27, 1924.






It carried factory workers to Decatur and Peoria plants and weekend excursions to Homer Lake on a branch line from Ogden from 1904 to 1929. Its freight cars carried coal, grain and later petroleum, and the profits were exceptional.
The following two decades would see a very different pattern from the steady growth of the 1920s. Starting with the Depression in 1929, many shorter and less profitable routes were cut. Investments were made to pump up the volume of the profitable freight traffic by constructing bypasses around those city street car lines that so often served the railroad, including in Urbana and Champaign. It also gave up many city streetcar lines it owned and cut its formal ownership connection with The Illinois Power Company.

Illinois Terminal Railroad Service 1937-1982 
They reorganized in 1937 under the name of the Illinois Terminal Railroad. Those moves enabled the newly minted Illinois Terminal Railroad to limp through the Depression.

The 1940s were a very different story. As the economy began to improve, so did the profit margins of the Illinois Terminal Railroad. World War II provided boom years, bringing factory workers to their jobs, especially from Decatur and Springfield to the ordinance plants in Illiopolis. Fifty-six additional coaches were purchased during World War II, and by 1945, The Illinois Terminal Railroad was carrying 8.6 million passengers a year. The future looked promising, and significant investments were made in new rolling stock for freight and passenger divisions.

These were good years for The Illinois Terminal Railroad. Many traditional steam lines were added around the St. Louis area for increased freight traffic, as that area was a flourishing industrial area. Former Urbana Junior High School teacher, Tina Ekstrom, remembers using the Illinois Terminal Railroad trains to commute between her University of Illinois semesters and her home of Springfield: "Those trains were wonderfully convenient, smooth and cheap. I loved them, and I miss them."

sidebar
The Illinois Traction System, at its height, provided electric passenger rail service to 550 miles of tracks in central and southern Illinois. 

But, as the 1950s progressed, so did highway construction. Quality paved highways were great for automobile travelers and truck haulers but often devastating to railroads. Even new and better rolling stock could not stop the bleeding of passenger profits to the highways. In 1956, The Illinois Terminal Railroad ended all passenger service. Some freight service survived after being dieselized and was sold to the Norfolk Southern System in 1981.
Illinois Terminal Railroad Company Streamliner engine and cars in the early 1950s.


Its legacy is more than memories. Sections remain as bicycle and hiking trails. Many of its buildings have been transferred to other uses. McKinley's generosity provided his alma mater with the McKinley Health Center. The wealth he spread around Central and Southern Illinois has other remnants, like the McKinley Presbyterian Church and Foundation campus.

Its longevity is the greatest testimonial to the Illinois Traction System and the Illinois Terminal Railroad. In their comprehensive book, "The Electric Interurban Railways in America," Dr. George Hilton and John Due computed that the average life of passenger service on an electric interurban was 28.3 years. Hilton and Due noted that the Illinois Terminal Railroad blossomed into the country's largest, end-to-end traction system, with a network of 462 route miles by 1950. The passenger service here lasted 55 years.
Illinois Terminal express car № 1202 at the station in Decatur, Illinois, circa 1950.


The electric interurban still survives in Northern and Southern Illinois. The South Shore Line runs from Millennium Station in Chicago to South Bend Airport daily. The St. Louis Metrolink system runs efficiently from St. Louis' Lambert Field to Metro St. Louis' Belleville, Illinois.

The ownership of the Illinois Terminal Railroad was acquired by a consortium of eleven St. Louis area railroads on June 15, 1956. The Illinois Terminal Railroad would begin a downward spiral until 1968 when it would be in a state of undeclared bankruptcy.
A pair of the Illinois Terminal's recently delivered SD39 engines, the biggest power the interurban ever owned, sparkle in the sun at Springfield, Illinois. 1969
In a remarkable undertaking of recovery, just as the railroad was about to wither away, Mr. E. B. Wilson would be appointed President. He would actually breathe new life into the floundering railroad. The railroad would literally take on a new identity as the "Road of Personalized Services," with new SD39s, SW1500s and a nationwide fleet of the new yellow and red rolling stock. The company's growth was astronomical, and the Illinois Terminal Railroad became a leader in the industry during high inflation and an oil crisis that crippled the nation. In addition to new equipment, new mileage was added to the system with the acquisition of a new route between Peoria and Decatur and the introduction of welded rail on the corridor between East. St. Louis and Alton. 

Unfortunately, the railroad would lose its leader to poor health, and the face of the railroad industry would change. Bankruptcies and mega-mergers meant the Illinois Terminal Railroad, a railroad without tracks, could not survive. On May 8, 1982, at 12:01 am, the Illinois Terminal Railroad Company ceased to exist, as ownership by the Norfolk & Western Railway went into effect. 

             System Map included.

Illinois Terminal № 1605, preserved in operating condition at Illinois Railway Museum.






What's Become of the Illinois Terminal Railroad?
The McKinley Bridge across the Mississippi River, originally built in 1910 to carry the Illinois Traction System's trolley cars over the river to St. Louis, survives today. 

Some sections of the Illinois Terminal Railroad and its affiliated lines have become 'rail trails,' such as the Interurban Trail south of Springfield.

The Illinois Traction System's generating plants selling electricity to customers in many towns and cities serviced by the electric railroad. In the 1930s, the railroad and its electrical utility separated. The formerly-affiliated electrical utility was spun off to form the Illinois Power and Light Company. Illinois Power provided electrical service to much of central and southern Illinois before its acquisition by Ameren. Consolidation into the parent firm occurred in 2004.

Compiled by Dr. Neil Gale, Ph.D.